small crack in a fused piece
Moderators: Brad Walker, Tony Smith
-
- Posts: 38
- Joined: Tue Nov 06, 2007 10:16 am
small crack in a fused piece
Hello
I made a large fused glass piece but it hit something hard and I found a small crack in it. The UV device I have only binds 2 separate pieces but not cracks. Is there any way to fix that without putting the piece into the kiln for a second time . I appreciate your comments and suggestions.
I made a large fused glass piece but it hit something hard and I found a small crack in it. The UV device I have only binds 2 separate pieces but not cracks. Is there any way to fix that without putting the piece into the kiln for a second time . I appreciate your comments and suggestions.
Re: small crack in a fused piece
Love that piece.
Nope. You fire it or you glue it. That's pretty much your only choices.
I'd refire.
You're using float glass? Love that. I have to hit 1800 or so to make my colors bloom like that.
Nope. You fire it or you glue it. That's pretty much your only choices.
I'd refire.
You're using float glass? Love that. I have to hit 1800 or so to make my colors bloom like that.
Re: small crack in a fused piece
If you're using float glass, I'd hit 1525 Fahrenheit then immediately go to my anneal schedule.
Temps for my kiln. Your temps may vary.
Temps for my kiln. Your temps may vary.
-
- Posts: 38
- Joined: Tue Nov 06, 2007 10:16 am
Re: small crack in a fused piece
Hi Judd
I used 2 sheets of Egyptian float glass 4mm in thickness . It has a nice satin look even when in direct contact with the mold. For the purple I used ferro enamel produced in Spain . I would never get the same beautiful result with ferro produced in the USA. My target temperature was 1508 Fehrenheit approximately.
I simply avoid a second firing because I can never tell what the outcome would be. I might loose the brightness of the glass or the vivid colors.
I used 2 sheets of Egyptian float glass 4mm in thickness . It has a nice satin look even when in direct contact with the mold. For the purple I used ferro enamel produced in Spain . I would never get the same beautiful result with ferro produced in the USA. My target temperature was 1508 Fehrenheit approximately.
I simply avoid a second firing because I can never tell what the outcome would be. I might loose the brightness of the glass or the vivid colors.
-
- Posts: 381
- Joined: Sun Mar 09, 2003 9:09 pm
- Location: Ontario
Re: small crack in a fused piece
Consider this a learning moment.. this crack WILL expand and the bowl Will break!.. Reheating, flattening, refusing, then reslumping, carries so many chances for disaster... but what have you got to lose other than time and $.... as for UV glue, it's still damaged goods!
"The Glassman"
-
- Posts: 38
- Joined: Tue Nov 06, 2007 10:16 am
Re: small crack in a fused piece
This piece was done by fusing and sagging in one firing. Usually, when I fire for the second time, I add another sheet of glass on top of the original piece and more colors if necessary before firing to 1508 F . The additional sheet helps in preserving the brightness. The piece becomes heavier after the second firing but flaws disappear especially when I add more colors or frits.
-
- Posts: 38
- Joined: Tue Nov 06, 2007 10:16 am
Re: small crack in a fused piece
Thank you all for your suggestions , comments and consolation.
Re: small crack in a fused piece
If I fire at low temps like 1500, I use copper leaf, other metals, or enamels. I have had great results with Gil Reynold's enamels that he sells at Fusion Headquarters.
http://www.fusionheadquarters.com/category_s/47.htm
The cobalt blue, yellows and greens are awesome. The reds tend to wash out if I hit temps over 1500. I don't use much purple, so I have no experience with that.
I'm just happy to see another artist using float glass. Good luck
http://www.fusionheadquarters.com/category_s/47.htm
The cobalt blue, yellows and greens are awesome. The reds tend to wash out if I hit temps over 1500. I don't use much purple, so I have no experience with that.
I'm just happy to see another artist using float glass. Good luck
-
- Posts: 38
- Joined: Tue Nov 06, 2007 10:16 am
Re: small crack in a fused piece
Thank you Judd