Sandblaster Foot Pedal
Moderators: Brad Walker, Tony Smith
Sandblaster Foot Pedal
I have a HF sandblasting cabinet with a dust collector and compressor. I just love it, but when I have to work for any serious amount of time, I find that my hand gets pretty tired squeezing the gun.
Does anyone know where I can get a foot pedal? Also, how complicated is it to install?
Thanks!
Does anyone know where I can get a foot pedal? Also, how complicated is it to install?
Thanks!
Re: Sandblaster Foot Pedal
Harbor Freight, works like a charm!
Have fun with it, much better than the pistol grip,
Barbel
Have fun with it, much better than the pistol grip,
Barbel
-
- Posts: 254
- Joined: Sun Jun 29, 2003 4:24 pm
- Location: Lenoir, NC
Re: Sandblaster Foot Pedal
Don't see a foot switch listed on their site...do you know the #?
"No, you cant scare Me, I'm sticking to the UNION. I'm stickin to the UNION till the day I die" Woody Guthrie
-
- Posts: 1037
- Joined: Sun Mar 09, 2003 5:59 pm
- Location: Massachusetts, USA
- Contact:
Re: Sandblaster Foot Pedal
Foot pedals are usually only available for siphon blasters. That's not what you want for a pressure pot. Glastar used to sell the foot pedal and valve that they use on their pressure pot separately, but I don't see it listed on their website. You might give them a call and ask.
Rayzist sells their version of the pressure pot foot pedal and valve, but it's pricey.
Tony
Rayzist sells their version of the pressure pot foot pedal and valve, but it's pricey.
Tony
The tightrope between being strange and being creative is too narrow to walk without occasionally landing on both sides..." Scott Berkun
Re: Sandblaster Foot Pedal
bought mine several years ago, have not checked since then
Barbel
Barbel
Re: Sandblaster Foot Pedal
Glastar's is still available, buried somewhere on their website. It requires some maintenance though- you have to keep on top of changing the diaphragm when the air won't shut off and it's good to keep an extra teflon body around. Otherwise it's a great unit for a pressure pot system.
Re: Sandblaster Foot Pedal
Thanks for the info. I'll check out the Glastar site and see if I can find out more about what they have to offer.
-
- Posts: 273
- Joined: Sat Oct 25, 2003 8:18 pm
- Location: Calgary, Canada
- Contact:
Re: Sandblaster Foot Pedal
http://ikonicsimaging.com/wp/store/prod ... ies-parts/
These guys sell a foot pedal that operates a pinch valve. I've been using this system for a years and really prefer it to the old rayzist diaphragm setup.
These guys sell a foot pedal that operates a pinch valve. I've been using this system for a years and really prefer it to the old rayzist diaphragm setup.
Rick Wilton
Re: Sandblaster Foot Pedal
Rick - is it the CrystalBlast replacement foot pedal?
-
- Posts: 273
- Joined: Sat Oct 25, 2003 8:18 pm
- Location: Calgary, Canada
- Contact:
Re: Sandblaster Foot Pedal
Yes, I use a this pedal.
with this valve
These work with pressure pots NOT SIPHON.
They do also have the valve MArty was talking about
with this valve
These work with pressure pots NOT SIPHON.
They do also have the valve MArty was talking about
Rick Wilton
Re: Sandblaster Foot Pedal
Great. Thanks!
-
- Posts: 254
- Joined: Sun Jun 29, 2003 4:24 pm
- Location: Lenoir, NC
Re: Sandblaster Foot Pedal
Ditto
"No, you cant scare Me, I'm sticking to the UNION. I'm stickin to the UNION till the day I die" Woody Guthrie
-
- Posts: 1037
- Joined: Sun Mar 09, 2003 5:59 pm
- Location: Massachusetts, USA
- Contact:
Re: Sandblaster Foot Pedal
Nice!!! I hadn't seen the pinch valve commercialized before. This is a great source for parts.
Tony
Tony
The tightrope between being strange and being creative is too narrow to walk without occasionally landing on both sides..." Scott Berkun
Re: Sandblaster Foot Pedal
Tony and Rick- The pinch valve has the same function as the diaphragm in Glastar's unit? How about longevity and cost of replacement?
Re: Sandblaster Foot Pedal
I had a footswitch connected to my pressure pot. It worked ok. I disconnected it though. Too many tubes tangling around and points at which clogs could occur. Instead I put my pressure pot on a stand, with the abrasive shutoff valve close by my right arm, so I can adjust it quickly. Still not a perfect solution.
-
- Posts: 273
- Joined: Sat Oct 25, 2003 8:18 pm
- Location: Calgary, Canada
- Contact:
Re: Sandblaster Foot Pedal
I've been using there pinch valve for over a couple years and finally did wear out one of the gaskets. It cost $37.00 to replace the bladder, I believe these bladders last a lot longer than the old diaphragm as in the old system the abrasive had to take a 90 degree turn bouncing off the diaphragm causing wear and tear. On my valve the bladder is completely out of the way and lets the media flow freely through the valve.
Rick Wilton
Re: Sandblaster Foot Pedal
Rick,
The body of the pinch valve that you suggest seems to be made out of plastic while those found here:
http://www.akopinchvalves.com/threaded-union-end.html
are made out of aluminum. I was told that it does matter for our application. Any thoughts?
Lucie
The body of the pinch valve that you suggest seems to be made out of plastic while those found here:
http://www.akopinchvalves.com/threaded-union-end.html
are made out of aluminum. I was told that it does matter for our application. Any thoughts?
Lucie
-
- Posts: 273
- Joined: Sat Oct 25, 2003 8:18 pm
- Location: Calgary, Canada
- Contact:
Re: Sandblaster Foot Pedal
The abrasive NEVER comes in contact with any of the housing. It flow directly into the pinch membrane, while I suppose the aluminum would be a better material it may be unnecessary.
If pricing is comparable I'd likely go with the aluminum as it'll likely last longer. You need to untread both ends of the housing to change in the bladder and the plastic will wear out long before the aluminum would.
Any idea about pricing of the aluminum?
Thanks,
If pricing is comparable I'd likely go with the aluminum as it'll likely last longer. You need to untread both ends of the housing to change in the bladder and the plastic will wear out long before the aluminum would.
Any idea about pricing of the aluminum?
Thanks,
Rick Wilton
Re: Sandblaster Foot Pedal
Same as yours. They quoted me US$149 for:
Pinch Valve, 1/2", direct air operated, union end socket
Housing: aluminum;
Sockets: 1/2" NPT zinc plated carbon steel;
Sleeve: abrasion resistant natural rubber;
Temperature: up to 175 Deg. F;
Product pressure: up to 90 psi;
Control air connection: G1/4";
Control air pressure: up to 120 psi
Extra rubber sleeve at US$38
Lucie
Pinch Valve, 1/2", direct air operated, union end socket
Housing: aluminum;
Sockets: 1/2" NPT zinc plated carbon steel;
Sleeve: abrasion resistant natural rubber;
Temperature: up to 175 Deg. F;
Product pressure: up to 90 psi;
Control air connection: G1/4";
Control air pressure: up to 120 psi
Extra rubber sleeve at US$38
Lucie